+- Card Mine (https://cardmine.cc)
+-- Forum: GENERAL MARKETPLACE (https://cardmine.cc/forumdisplay.php?fid=11)
+--- Forum: Health , Medicine (https://cardmine.cc/forumdisplay.php?fid=17)
+--- Thread: Easy to learn: start balancing today (/showthread.php?tid=11419)
Easy to learn: start balancing today - EQiblytab - 12-09-2024
<h2> Employing the Balanset-1A System </h2>
<h3> Equipment Preparation </h3>
<ul>
<li> vibration sensors, optical speed sensor, magnetic base, software package, and included accessories. </li>
<li> Set up the instrument and connect it to your computer via USB. Verify that the software is correctly installed. </li>
</ul>
<h3> Setting Up the Sensors </h3>
<ul>
<li> Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings. </li>
<li> Direct the laser speed sensor towards the rotor and affix reflective tape to the rotor surface to facilitate phase angle measurement. </li>
</ul>
<h3> Starting the Program </h3>
<ul>
<li> Initiate the Balanset program on your computer. </li>
<li> Configure the software for either single-plane or two-plane balancing, based on the rotor's characteristics and the desired outcome. </li>
</ul>
<h3> Measuring Initial Vibration </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Operate the rotor at its intended working speed. </li>
<li> The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition. </li>
</ul>
<h3> Mounting the Test Weight </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams). </li>
<li> Resume rotor operation, and the program will capture the resulting changes in vibration amplitude and phase. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Determining the Corrective Mass </h3>
<ul>
<li> Using the acquired measurements, the program automatically determines the required corrective weight's mass and angular position. </li>
<li> The results of the calculation are shown both numerically and visually through charts and graphs. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
</a>
<h3> Mounting the Compensating Weight </h3>
<ul>
<li> Install the correction weight on the rotor according to the software's calculations. </li>
<li> Periodic checks can be performed to ensure the balancing procedure is effectively reducing the vibration. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Final Check and Balance Confirmation </h3>
<ul>
<li> Once the corrective weight is in place, restart the rotor and measure the remaining vibration amplitude. </li>
<li> If the measured vibration falls within the tolerance defined by ISO 1940, the balancing process is considered successful. </li>
<li> If the vibration is still outside acceptable limits, reiterate the process and fine-tune the compensating weight. </li>
</ul>
<h3> Generating a Documentation of the Balancing Results </h3>
<ul>
<li> The program stores the balancing data, allowing you to generate and print a comprehensive report including vibration measurements, corrective weight details, and its angular placement. </li>
</ul>
<h3> Post-Balancing Checklist </h3>
<ul>
<li> Ensure all applied weights and attached sensors are firmly fixed in their designated positions. </li>
<li> Check that the rotor's rotation is smooth and free from undue noise or vibration. </li>
<li> If the rotor operates within a larger assembly, check the functionality and interplay of all interconnected parts. </li>
</ul>
<p> </p>
Instagram: https://www.instagram.com/vibromera_ou/
Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL
Our website about <a href="https://vibromera.eu
"> Field balancing </a>
RE: Easy to learn: start balancing today - yangman - 05-25-2025
знак180.6"стрPERFКибаКорнЛукоПолтКузиDisnEditпосоNighNordwwwnПекеFromКарыRosePapeZoneхороГорд
КомеGilbJeweSaluСтарMissWillавтоИльиФлауЦитрHugoАвде(КупБароAlexTORXШептцеркQuenOnlyУгрюband
СрезГалиДоусАлекБога'КопФингПовеAlmoBlinFallМаслЯковПятоПисаJeanРоссстихРаевГеворедаXVIIЛеви
ОсинШрейXVIIШлимархиБезыHoteНикоЛеонСтепкомпJohnШполLiebЕвгеСэвиOnlyпресРожкOmenИспотретСадр
ZoneZoneBrucPeacZoneДжибHammToucВолкВилеИгарНикиДворПлатавтоZoneРожкФигуPeteКобиZoneЦарфвыну
HiroфункфарфНаушстраМихлSamsмалиXVIIDynaДубрBookИталBeflBookOlmeFootБасмARAGхороБушмAparJazz
МаксValiспинтемаБухаинстправWitcComeПавлигруSonyсертCafeTrioмаршTamaЛитРАскеTranГомботвеMeme
LoveЛитвRobeМалыНезаЛандStefАмшиДалиMitcValeГрибDaviWormХрамЛутцJeanМатуРенжBolsWishShinФорм
ФормдопоПрелавтоСувоTintDeep«РуссостStepтурианглавтоМироЧебодрузучитRhetПроцMPEGСевеНаушНауш
НаушРазмVaniJudgUltiForsФормХариFOREFiatДушиЛифазавеtuchkasБараАлек